E-mon E-PS-S-HV-RTU Instrukcja Użytkownika

PowerSmart Socket POWER QUALITY METER Installation Manual BG0549 Rev. A1

Chapter 2 Installation 4 Chapter 2 Installation The PowerSmart Socket PQM Socket meter is designed to mount into a standard meter socket. Follow th

Chapter 3 Communication 5 Mechanical Installation Mechanical Installation Mechanical Installation Mechanical Installation Refer to the figures p

Chapter 2 Installation 6 Physical Description Device Structure Fi g ure 3: Po w e r S ma rt Soc ke t P QM i n t e r n a l stru c t u re Optio

Chapter 3 Communication 7 Meter Ex ternal connections Figur e 5:Me te r B a se – r e a r view

Chapter 2 Installation 8 Electrical Installation Before installing, ensure that all incoming power sources are shut OFF. Failure to observe thi

Chapter 3 Communication 9 W iri n g C onf i g u rat io n Wiring Setup FORM factor 4-wire WYE 3-element using 3 CTs 4Ln3 9S 4-wire WYE 3-elem

Chapter 2 Installation 10 Figure 9:Four W i r e WYE Co n n e c tion Usin g 3 PT s and 3(4) C Ts - W i ring Se t up : 4Ln 3 Figur

Chapter 3 Communication 11 Figure 1 1: Four W ir e DELTA C o n n e c tion U s i n g 3 PTs a n d 3 C Ts - W iri n g Se t up : 4LL 3

Chapter 2 Installation 12 Figur e 13: Thr e e Wi re D E LT A Connec tion U s i ng 2 PTs and 2 CTs - W iri n g Set u p : 3OP3

Chapter 3 Communication 13 Input / Output ports options Before I/O Module installation ensure that all incoming power sources are shut OFF. Failur

ii DANGER This symbol indicates the presence of dangerous voltage within and outside the product enclosure that may constitute a risk of e

Chapter 2 Installation 14 Option al I / O m od ules 8DI The 8DI module consists of eight status inputs detection. To install the 8DI module foll

Chapter 3 Communication 15 R e l ay O u tp u ts (6 R O – option a l mo dule) The 6RO module consists of: four FORM C (SSR) and two FORM A (EMR) r

Chapter 2 Installation 16 Figur e 19: 4A O Con n e c tion It is recommended to connect unused Analog output channels to Common terminal. ⇒

Chapter 3 Communication 17 Transi en ts Rec ord er M od u l e (TRM – optional mod u le) The PowerSmart Socket PQM Transients Recorder module provi

Chapter 2 Installation 18 Communications options The PowerSmart Socket PQM has several communication alternatives depending on your orderi

Chapter 3 Communication 19 U SB Co m m u n ic a tio n po r t (U SB – o n b oard ) The PowerSmart Socket PQM provides a standard full speed USB

Chapter 2 Installation 20 3) Plug-in the module in the COM slot and attach it to bracket using the two screws 4) Connect the GSM

Chapter 3 Communication 21 Figur e 26: MOD E M m o d ule R S -48 5 / 2 3 2 Co mmunicat i on p ort ( CO M4 – E TH or MO D E M o ption a l

Chapter 2 Installation 22 R S -23 2 m ode In the RS-232 mode, the 485/232 wire must be tied to GND wire as shown in figure 28 Fi g u r e 28: S

Chapter 3 Communication 23 Fi g u r e 30: MO D E M c onn ection The MODEM module provides additionally to COM4 indication GREEN LEDS, MODEM ind

iii DANGER Failure to observe the following instructions may result in severe injury or death. Read the instructions in this manual before perfor

Chapter 2 Installation 24 The AC/DC APS module provide one indication GREEN LED: is "OFF" if AC/DC APS cable is disconnected or no power s

Chapter 3 Communication 25 Chapter 3 Communications 1. Communications Computer Connections – RS-232 Figur e 32: RS-2 3 2 S i m p

26 Chapter 4 Replacing the Battery Chapter 4 Replacing the Battery When the battery level drops below the minimum allowed threshold, the LCD graphi

Appendix: Technical Specifications 27 Appendix: Technical Specifications Inputs Ratings AC Voltage inputs Va, Vb, Vc and Vref - 50/60Hz High in

Appendix: Technical Specifications 28 Power Supply Power supply Supplied from Monitored Voltage inputs Three Phase PS, Rated Inputs (L-N) 50/60 H

Appendix: Technical Specifications 29 Terminals for wires size Blades (Socket meter standard – C12.10) Relay Output Digital output – combined S

Appendix: Technical Specifications 30 Communication ports COM1 Built-in Infra Red communication port DISPLAY unit RS232 communication, TTL level

Appendix: Technical Specifications 31 USB connector Cable terminated with USB type A Input Isolation 2500V AC @ 1mn Time code signal Demodulate

Appendix: Technical Specifications 32 Surge – IEEE C62.41.2-2002 100kHz ring wave 1.2/50 µs – 8/20 µs 6kV / 0.5kA 6kV / 3kA Magnetic field – AN

Appendix: Technical Specifications 33 Measurement Specifications Accuracy Parameter Full Scale @ Input Range % Reading % FS Conditions Range Vo

iv Table of Contents Chapter 1 Introduction ...

Appendix: Technical Specifications 34

v FIGURES Figure 1: Front view - Nameplate description...

Chapter 1 Introduction 1 Chapter 1 Introduction About This Manual This manual is intended to assist the user in the installation of the

2 Chapter 1 Introduction − Low Range measurement input nominal rating – "U" Model: 57.7V AC to 120V AC (L-N) − High Range measurement inp

Chapter 1 Introduction 3 Socket Meter Overview Figure 1: Front view - Nameplate description